- Description
Specifications
FEATURES
|
Futaba S-FHSS 2.4GHz security (also FHSS compatible)
Transfers model data wirelessly to and from one 8J to another
Capable of 4 channels only in FHSS mode
R2008SB receiver offers 8 PWM channels, S.Bus and HV capability and
Dual Antenna Diversity
Airplane and helicopter modes
20 model memory with 10 character model and user naming
Large backlit LCD display (128 x 64 dot)
8 channels (one varible knob, five 2-position switches,
two 3-position switches, one momentary switch and two digital
levers)
Failsafe on all 8 channels
Easy jog dial and three button programming
ATL
Aux channel switch/level assignability
One year limited warranty through Hobby Services beginning at date
of purchase
Airplane Mode Features;
6 Programmable Mixes Snap Roll
Flaperons with Differential Rate Elevator/Flap Mixing
Flap Trim Airbrake/Landing
Differential Ailerons Aileron/Rudder Mixing
V-Tail Mixing Flap/Elevator Mixing
Elevon Gyro Sensitivity
Ailevator Throttle Curve (five points)
Throttle Needle Mixing (five points) Throttle Delay
Idle Down (any switch selectable)
Helicopter Mode Features;
8 Swash Plate Types
5 Flight Conditions (normal, idle up 1, idle up 2, idle up 3, hold)
Throttle Curve (five points, five curves)
Throttle Hold
Hover Pitch Mixing
Hover Throttle Mixing
Gyro Sensitivity/Mixing
Governor Setting/Mixing
Hi/Lo Pitch Mixing
Offset Mixing
Condition Delay
Throttle mixing (swash>throtttle)
Throttle/Needle Mixing (5 point curve)
Swash AFR
Swash Mixing
Electronic Swash Ring
Throttle Delay
Revolution Mixing
6 Programmable Mixes
Transfers model data wirelessly to and from one 8J to another
Capable of 4 channels only in FHSS mode
R2008SB receiver offers 8 PWM channels, S.Bus and HV capability and
Dual Antenna Diversity
Airplane and helicopter modes
20 model memory with 10 character model and user naming
Large backlit LCD display (128 x 64 dot)
8 channels (one varible knob, five 2-position switches,
two 3-position switches, one momentary switch and two digital
levers)
Failsafe on all 8 channels
Easy jog dial and three button programming
ATL
Aux channel switch/level assignability
One year limited warranty through Hobby Services beginning at date
of purchase
Airplane Mode Features;
6 Programmable Mixes Snap Roll
Flaperons with Differential Rate Elevator/Flap Mixing
Flap Trim Airbrake/Landing
Differential Ailerons Aileron/Rudder Mixing
V-Tail Mixing Flap/Elevator Mixing
Elevon Gyro Sensitivity
Ailevator Throttle Curve (five points)
Throttle Needle Mixing (five points) Throttle Delay
Idle Down (any switch selectable)
Helicopter Mode Features;
8 Swash Plate Types
5 Flight Conditions (normal, idle up 1, idle up 2, idle up 3, hold)
Throttle Curve (five points, five curves)
Throttle Hold
Hover Pitch Mixing
Hover Throttle Mixing
Gyro Sensitivity/Mixing
Governor Setting/Mixing
Hi/Lo Pitch Mixing
Offset Mixing
Condition Delay
Throttle mixing (swash>throtttle)
Throttle/Needle Mixing (5 point curve)
Swash AFR
Swash Mixing
Electronic Swash Ring
Throttle Delay
Revolution Mixing
6 Programmable Mixes
INCLUDES
|
8J Transmitter
R2008SB 8-channel Receiver, FUTL7608
Neckstrap
On/Off Switch
Instruction Manual
R2008SB 8-channel Receiver, FUTL7608
Neckstrap
On/Off Switch
Instruction Manual
REQUIREMENTS
|
Four AA batteries for transmitter
Servos of modeler's choice
Servos of modeler's choice
COMMENTS
|
To use the NiMH battery FUTM1482, you will need to purchase
charger FUTM1832.
You may also use a 2C 6.6V LiFe battery such as HCAM6521
If you are wanting to ue a LiFe or NiMh battery with this
transmitter, you will need to purchase the NiMh battery
door from Futaba Service at 217-398-8970 part number HSP82469
To charge through the transmitter, you will need a lead from
Futaba Service, part number HSP29615. This is only the TX jack
with leads that you will need to solder connectors onto to use
with your charger.
jxs 02/07/12
charger FUTM1832.
You may also use a 2C 6.6V LiFe battery such as HCAM6521
If you are wanting to ue a LiFe or NiMh battery with this
transmitter, you will need to purchase the NiMh battery
door from Futaba Service at 217-398-8970 part number HSP82469
To charge through the transmitter, you will need a lead from
Futaba Service, part number HSP29615. This is only the TX jack
with leads that you will need to solder connectors onto to use
with your charger.
jxs 02/07/12